Black Widow Security BW 3 Channel Manual de instalación descargar pdf (Pagina 2)

- 1 -

INSTALLATION INSTRUCTIONS

IMPORTANT:

Make all wiring connections to the vehicle before connecting the main

10-pin harness and all plug-in connectors to the receiver control module.

1. Before mounting the Receiver and Control Module, you must set the PROGRAMMING DIPSWITCHES

for the kind of operation the customer wants.

These are the switch settings available; Standard (Default) settings are in “BOLD” type:

Switch #1 Door Lock and Unlock Pulse Time: ON = 3/4 seconds. OFF = 3 seconds.

Switch #2 Door Lock and Unlock with ignition: ON = YES. OFF = NO.

Switch #3 Door Locking with Passive Arming: ON = YES. OFF = NO.

Switch #4 Passive or Active Arming: ON = Passive Arming. OFF = Active Arming.

2. Mount the Receiver and Control Module in a secure area, away from vehicle computers and heating/air condi-

tioning ducts.The location should be convenient for your installation, but well hidden from thieves.Try to mount the unit

as far away from metal objects as possible.This will increase the range of its Remote Control Transmitter.

3. Route the wires of the harnesses to areas in which the different accessories will be mounted .You may

need to extend some wires.

DO NOT plug the wiring harnesses into the Receiver Control Module until

all connections have been completed.

When running the harness wires through the vehicle, be careful to run them where they CANNOT be DAM-

AGED or SHORTED to GROUND or other WIRING. Keep them away from ALL MOVING PARTS of the vehicle

or where HIGH HEAT can damage their insulation.Always protect the harness wires where they pass through

holes in metal panels by using RUBBER GROMMETS.

4. Mount the Siren under the vehicle’s hood. Mount it away from heat sources such as radiators, exhaust mani-

folds, and turbochargers. Mount it in an area where it will not be in the way for mechanics, and so that it cannot be

easily reached from below the vehicle. Mount it so that its opening points down to prevent it from collecting water,

snow, or ice. Connect its BLACK wire to a good clean GROUND point, and its RED wire to the ORANGE wire of

the main harness. The siren is capable of two different arm/disarm/status chirp tones:A)Chirp Level One = Soft

Chirp– Standard from factory.

B) Chirp Level Two = Loud Chirp– Cut black wire loop found at base of siren.

5. Mount the Shock Sensor Somewhere inside the vehicle such as under the dash, strapped to the steering col-

umn, or under a seat..

Do Not Mount The Sensor Under The Hood!

Connect the 4-pin harness from

the shock sensor to the 4-pin male plug on the circuit board of the Receiver Control Module.

6. Mount the LED Status Indicator in an easily seen location such as the center of the dash or the inside top

edge of the driver’s or passenger’s door. Connect the RED 2-pin connector from the LED to the RED

2-pin male plug on the circuit board of the Receiver Control Module.

7. Install the Valet/Override Switch in a hidden location that is easily reached by the driver. Remember that the

code learning and valet/override sequence require using this switch in conjunction with the ignition switch, so it

should be hidden, but convenient to use when needed. Connect the BLUE 2-pin connector from the Override

Switch to the BLUE 2-pin male plug on the circuit board of the Receiver Control Module.

8. Mount the optional BRS-003 Starter Disable Relay Socket and SPDT Relay in a location where it is

hidden from potential thieves. Find the vehicle’s STARTER wire and cut it in half. Connect the colored wires of the

Relay Socket as follows:

WHITE = To STARTER wires on Starter side. RED = To STARTER wires on Switch side.

ORANGE = ORANGE wire of the main harness.

9. Mount and connect any optional function modules included in the installation, following the mounting and

wiring directions supplied with them.

10. Complete the general wiring of the main harness by connecting...

A.The WHITE wire to the vehicle’s PARKING LIGHT circuit. See the Parking Light Circuit. Diagram on Page 5.

B. The RED wire to CONSTANT +12vdc. IMPORTANT: Remove the fuse from the harness before connection.

C. Connect the BROWN wire to the RED wire from the siren.

D.The BLACK wire to a good chassis GROUND point.

E.The ORANGE wire to optional starter relay

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

Black Widow Security BW 3 Channel Manual de instalación Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Black Widow Security BW 3 Channel