Black Widow Security BW RAS 130 Manual de instalación Pagina 3

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 8
  • Tabla de contenidos
  • SOLUCIÓN DE PROBLEMAS
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 2
GRAY WIRE - Ground When Running Output (-).
Connect to a relay for starter anti-grind protection.
(See installation diagrams). The GRAY wire pro-
vides ground for starter anti-grind protection and
when the remote start is engaged to activate an
optional factory security bypass module. When the
Stop-and-Go mode is engaged, the output will turn
on and remain active even after pressing the brake
pedal. Although the remote start shuts down when
the brake pedal is pressed, the output will remain
on until the ignition key is turned on and off.
GREEN WIRE - Tach/Spark sense wire. If the cur-
rent sensing feature does not allow desired opera-
tion, connect the GREEN wire directly to the vehi-
cles tach wire and set dip switch #1 to OFF. If the
tach wire is not accessible, wrap the GREEN wire
around a spark plug wire or coil wire several times
and secure with electrical tape.
BLUE WIRE - Hood switch input wire (-).
Connect this wire to the hood pinswitch, this will
prevent the vehicle from remote starting if the
hood is opened. This is a safety input and
must be
connected on all installations.
VIOLET WIRE - See BROWN wire.
YELLOW WIRE - Brake switch input wire, con-
nect this wire to the brake switch wire that pro-
vides +12V when the brake pedal is pressed.This is
a safety input and
must be connected on all instal-
lations.
Plug in Connectors:
3-Pin White Door Lock Connector: Plug-in con-
nector port for door lock harness or optional
door lock relay module (PDLM-3).
BLUE WIRE - negative unlock output (-).
RED WIRE - constant +12V low current output
(+) for relay modules, or inverters. 100mA relay
trigger only. Do NO
T use as a power source for
door lock relays.
GREEN WIRE - negative lock output (-).
3-Pin Red Connector: Plug-in connector port for
optional features harness.
GREEN/BLACK WIRE - 3rd channel output (-).
Connect to a relay for optional trunk release etc.
RED WIRE - Factory Disarm output (-).
Connect to the wire that requires a ground pulse
to disarm the factory alarm system. The RED wire
provides a ground pulse when the remote trans-
mitter is used to unlock the doors or start the vehi-
cle.
YELLOW WIRE - Vacuum Switch output. For
diesel vehicles, or vehicles where a tach wire or
spark plug wire is not available, the YELLOW wire
may be connected to an optional vacuum switch.
Connect the other side of the vacuum switch to
ground.
2-Pin Red Connector: Plug-in connector port for
LED. Mount LED in an area where it may be easily
seen from either side of the vehicle.
2-Pin Blue Connector: Plug-in connector port for
program/service switch. Mount program switch in
an area that is easily accessible from the drivers
position.
4-Pin Antenna Connector*: Plug-in connector
port for extended range receiver. Plug harness into
4-pin connector, route cable up pillar post, place
double sided tape on flat side of receiver module
and place in corner of windshield.
*For programming you will need a receiver and transmitter
Remote Programmable Features
To enter program mode:
1. Turn ignition to the on position.
2. Wait 2 seconds.
3. Within 10 seconds press program switch 5
times.
4. The LED and parking lights will turn on for 2
seconds to indicate the system is now in pro-
gram mode.
To change programmable features:
Press program switch the number of times that
3
Vista de pagina 2
1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios