Black Widow Security BW RAS 651 Manual de usuario descargar pdf (Pagina 5)

seconds after the ignition is turned off and

anytime button 1 is used to lock the doors.

• WHITE/BLUE WIRE - Horn output (-)

250mA. Connect to an optional relay to

activate the vehicle’s horn.The horn output is

programmable for pulse duration and to set

which functions will trigger the horn pulses.

• BLACK/WHITE WIRE - Not used.

• VIOLET WIRE - Not used.

• WHITE WIRE - Parking Light output (+) 10A

relay. Connect to the vehicle’s parking light

wire. If the vehicle is equipped with more than

four parking lights or with independent left and

right parking light circuits a relay is required.

For vehicle’s with negative trigger parking lights,

the RED/WHITE trunk release wire can instead

be programmed for use as a negative parking

light output if needed, and the WHITE wire

output then becomes a positive trunk release

output.See Programmable Features

NOTE:Do not connect the parking light output

to the vehicle’s headlight circuit.

• GREEN/WHITE WIRE - Hood trigger input

(-).Connect to the hood pin switch that shows

ground when the hood is open.

• GREEN WIRE - Not used.

• BLACK WIRE - Ground input (-).Connect to

a chassis ground that is free of paint or dirt.

• PINK WIRE - Brake switch input (+).

Connect this wire to the brake switch wire that

provides +12V when the brake pedal is pressed.

• BLUE/WHITE WIRE - Tachometer input

(A/C). Connect to the vehicle’s coil, fuel

injector or crank sensor wire.

• BLUE WIRE - Glow plug light input (+/-). For

diesel vehicles without a glow plug wire, no

connection is needed. A 15-second timer will

engage before cranking the starter. Most diesel

vehicles will have a glow plug wire located in the

instrument cluster. For these vehicles, test the

wire to confirm proper operation and connect

to it. Negative glow plug wire systems will show

+12V when the the glow plug (wait-to-start)

light is on, then show ground when the light

turns off. Positive glow plug wire systems will

show ground when the wait-to-start light is on.

The BLUE wire is programmable for the system

polarity and should be connected directly to the

glow plug wire.See Programmable Features

6-Pin Starter Harness

• YELLOW WIRE - Start output (+). Connect

to the vehicle’s starter wire.

• GREEN WIRE - Main accessory output (+).

12V output for heater and/or air conditioning

system. For cars with more than one accessory

wire add a relay(s) to power the extra

accessory wire(s) or if the WHITE wire is not

being used, it can be programmed for second

accessory output.

• RED WIRE - Main power input (+).Using the

supplied inline fuse holder, connect directly to

the vehicle’s battery or alternate power source

with a minimum 30 Amp supply.

• RED WIRE - Main power input (+).Using the

supplied inline fuse holder, connect directly to

the vehicle’s battery or alternate power source

with a minimum 30 Amp supply.

• BLUE WIRE - Main ignition output (+).

Connect to the main ignition wire that switches

+12 V and does not drop out during cranking.

• WHITE WIRE - Second ignition output (+).

Connect to the wire that switches +12V and

does not drop out during cranking. This wire

may be optionally set via jumper for use as a

second accessory wire or second starter wire.

Remove top of housing and see Jumper Settings.

Module Connectors

3-Pin White Connector: Plug-in connector for

door locks.

• GREEN WIRE - Lock output (-) 500mA.

BW651 final.qxd 10/18/2005 10:58 AM Page 5

1 2 3 4 5 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios

Black Widow Security BW RAS 651 Manual de usuario Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Black Widow Security BW RAS 651